SBO on Smart IR Heating Solutions

Replacement lamp for Sidel SBO 20 Series 2

Tue, 28 Jul 2026 09:13:30 +0800

Stop the breakage on your Sidel SBO 20 Series 2 lines

If you’re running SIG Blomax or Sidel SBO lines, you know the headache of tubes breaking. It usually comes down to two things: messy heat profiles or just plain mechanical stress on the lamps. We got tired of seeing those failures, so we rebuilt our replacement lamps for the SBO 20 Series 2 to actually hold up under pressure. Getting the heat just right Here’s the thing about the SBO 20 Series 2: it’s picky. You need a very specific wattage-to-voltage ratio to get that PET preform to the right temperature before it blows. If your lamps are too weak, you end up with uneven walls. Too hot? You’ll scorch the plastic. We made our replacements a mirror image of the OEM footprint. That means they just slide right in. No messing with your wiring, no tweaking the reflectors. It just works. Built to take a beating We went with high-purity quartz glass because these machines go through a brutal thermal rollercoaster. Most standard lamps give up at the pinch seal—especially when the machine starts vibrating or you’re cycling the power on and off. We reinforced those end-cap seals to stop the premature burn-outs. Now, the lamps can handle the chaos of a high-speed production run without cracking. A couple of tips for the floor These lamps pack a lot of heat density to keep your cycle times fast. But there’s a catch. You’ve got to keep your reflectors spotless. If carbon builds up, that heat bounces straight back into the lamp jacket. Once that happens, it doesn’t matter how tough the lamp is—it’s going to die early. When you’re wiring them up, just stick to your machine’s voltage specs. And for heaven’s sake, check your cooling fans. High-output quartz lamps get hot—really hot. If your airflow is blocked, you’re just cooking your electrical components.

How to replace Sidel SBO heater lamp

Tue, 28 Jul 2026 09:07:11 +0800

Stop Fighting Your SACMI Startup

If you’ve ever run a high-speed PET line, you know the stress of that window between loading the preforms and actually stretching them. It’s tiny. When your lamps take forever to get up to temperature during a startup or a cycle tweak, you’re basically gambling. You end up with burst preforms or walls so uneven they’re useless. It’s frustrating, and it wastes a lot of plastic. That’s why we rebuilt our replacement lamps for SACMI rotary machines. We wanted to kill that lag time.

Global supply of Sidel SBO heater lamps

Sat, 25 Jul 2026 06:19:08 +0800

Fixing Those Annoying Heat Spots in Your KHS and Sidel Blow Molders

Ever pull a batch of bottles and see that cloudy, pearlescent look? Or maybe the walls are way too thin in some spots and thick in others. It’s frustrating. Usually, it just means your thermal field is off—you’ve got hot and cold spots in the oven that are messing with your PET preforms. We’ve spent a lot of time building replacement lamps for Sidel SBO and KHS systems specifically to kill those dead zones and get your quality consistent again. The nitty-gritty on the heat Here is how we handle it: we tweak the filament winding density to control exactly how the heat radiates. If you’re chasing faster cycle times, you’ll want a lamp with higher wattage to get that heat density up. Just a heads-up, though. Double-check that your power supplies can actually handle the load. If you push them too hard, you’re just asking for a premature burnout. Why the glass matters We use high-purity quartz glass. Why? Because it lets shortwave infrared light pass right through. Instead of just scorching the surface of the plastic, the heat actually penetrates the material. As for the install, it’s easy. Most of these use standard R7s or SK15 connectors. They’re designed to be drop-in replacements, so you can just wire them up and go without messing around with your existing lamp holders. What to watch out for in the shop When you swap out your OEM lamps for these, you’ll notice the heat field stabilizes. It makes a huge difference in how much scrap you throw away during start-up. But there is a trade-off. If you crank up the wattage to boost your throughput, your oven’s ventilation has to work harder. Make sure your cooling fans are up to the task. If the heater block gets too hot, you risk warping your reflectors, and that’s a headache nobody wants.

Replacement lamp for SIDEL SBO Series 2

Thu, 25 Jun 2026 13:48:03 +0800

On the blow molding floor, the heating tunnel doesn’t cut you any slack. Preform temperature has to be repeatable, cycle after cycle. If lamp output drifts or the reflector geometry is off, you’ll see inconsistent stretch, weak necks, and scrap piling up. The replacement lamp we spec for the Sidel SBO Series 2 keeps the heating profile stable without forcing you to rework the oven. What matters, technically We stick to the OEM parameters that actually matter on the machine. It’s a short-wave infrared quartz lamp—2400 W, 230 V, 300 mm arc length, 320 mm overall. The base is a standard R7s connector, and the cold-end length is dimensioned to the same footprint so it seats cleanly in the reflector. Filament temperature and spectral output are chosen to line up with PET absorption, so you get fast, even heating without hot spots. The same dimensional and electrical envelope fits the SBO Series 2 and plays cleanly with common configurations on Krones, SIPA, Husky, and SACMI stretch blow molders—no rewiring, no swapping reflectors. Here’s why it holds up in production. In stretch blow molding, repeatability is the only scoreboard. With this lamp, preform heating settles faster after a changeover, and temperature drift across the tunnel tightens up. The payoff is fewer rejects, more consistent bottle weight, and a higher first-pass yield. Energy use comes down because the emitter hits target quickly and holds it with stable output. Under normal line conditions, you can expect 5,000+ hours of service life, which means fewer maintenance windows and more uptime. A few shop-floor details. Installation is straightforward, but reflector condition is critical. If the reflector is oxidized or pitted, the lamp will underperform even with perfect specs. Check reflector alignment and clean the mounting surfaces before swapping in the new one. Also, measure the voltage at the socket—sustained overvoltage will shorten lamp life, even when the lamp matches the rated spec. Use the correct connector orientation and don’t touch the quartz with bare skin; oil residues bake on and drive hot spots and premature failure.